Viking CTG-2 Specifiche Scaricare il pdf (Pagina 3)

A. Setting the Clock Time

1. Press the MODE button repeatedly until the SET TIME indicator lights.

2. Increase or decrease the clock time by pressing the + or -/CANCEL button until the desired time is displayed.

3. Leave the set time mode by pressing the MODE button.

Note: Either the + or -/CANCEL button MUST be pressed at least once prior to leaving the set time mode. The clock

will then start to run the moment you leave the set time mode, allowing you to synchronize the CTG-1 with your build-

ing clocks.

B. Setting the Day of the Week

Note: This step is only required if you want to turn off the Alert Tones on certain days of the week.

1. Press the MODE button repeatedly until the SET DAY indicator lights.

2. A flashing “A” indicates all 7 days of the week are “on” and today’s week day has not been set. The day of the week

has already been set if a flashing number (1-7) and “on” or “of” are displayed.

3. Select today’s day of the week using the TIME (+ and -/CANCEL) buttons. As a general rule, Sunday is day 1 and

Saturday is day 7. When the correct day of the week is flashing on the display, set it by pressing the DOUBLE alert

tone button. The week day number and “on” will now be displayed.

Note: The day of the week setting is a one time set up and does not need to be reset unless you have experienced a

brown out long enough to discharge the 9V battery backup (approximately 8 hours). To reset the day of the week, you

must power down the CTG-1, remove the 9V battery and repeat steps 1-3 above.

C. Turning the Alert Tones On/Off for Specific Days of the Week

D. Setting Timed Alert Tones

1. Press the MODE button repeatedly until the SET EVENTS indicator lights.

2. Increase or decrease the event time by pressing the TIME (+ or -/CANCEL) button until the desired time is shown.

3. Press one of the single, double, or triple ALERT TONES buttons to program that selected tone you wish to output

at the specific event time. A single, double, or triple confirmation beep should be heard.

Note: If more than 128 events have been entered, a long beep will be heard indicating that the event memory is full.

E. Reviewing and/or Cancelling Timed Alert Tones

1. Press the MODE button repeatedly until the REVIEW/CANCEL indicator lights.

2. Press one of the ALERT TONES buttons (single, double, or triple) repeatedly to rotate through the event times

associated with that alert tone button.

Note: Event times are stored in the order of programming, not chronologically.

3. Press the -/CANCEL button to permanently cancel an event tone. The next consecutive event for that specific

alert tone will then be displayed.

F. Adjusting Output Volume

1. Short pins 7 and 10 together. The door bell sound will then begin to chime.

2. Adjust the volume control potentiometer (see Installation section A).

G. Activating Contact Closure Alarm Tones

To activate different sounds, short the corresponding pins with a

dry contact closure as shown right (see Installation, section A).

Note: While the appropriate contact closure is maintained the

sounds will be repeated continuously.

1. Press the MODE button repeatedly until the SET DAY indicator lights. The current day of the week and “on” or “of”

will be displayed. “on” = alert tones are ON and “of” = alert tones are OFF for that day of the week .

2. Pressing the SINGLE button will toggle between flashing the day of the week and flashing “on” or “of”. The flash-

ing portion of the display is the section that can be changed.

3. With the day of the week flashing, use the TIME (+ and -/CANCEL) buttons to select the day of the week you would

like to set to ON or OFF. When the correct day of the week is displayed, press the SINGLE button to flash “on” or

“of”. The day can then be set to ON or OFF by using the TIME (+ and -/CANCEL) buttons.

4. Review your day of the week programming by pressing the SINGLE button until the weekday (1-7) is flashing, then

increment through each day of the week with the TIME (+) button and monitor each day for its on or off setting.

Exit the SET DAY mode by simply pressing the MODE button.

When finished programming, press the MODE button until the LOCK indicator lights. In the lock mode, the time and

alert tone keys will be disabled and the current time will be displayed with the colon flashing once per second.

H. Locking the CTG-1 for Operation

Sound

Door Bell (Dong Dong)

Evacuation Sound (Slow Whoop)

Siren (Yelp)

Short Pins...

...7 to 10

...8 to 10

...9 to 10

1 2 3 4

Commenti su questo manuale

Nessun commento

Viking CTG-2 Specifiche Pagina 3

Commenti su questo manuale

Prodotti e manuali riguardandi Orologi a muro Viking CTG-2