Viking CTG-2 Specifiche Scaricare il pdf (Pagina 2)

A. Typical Installation on the Paging Port of a Phone System

Connect the CTG-1 between your phone system and your paging amplifier as shown in the diagram below. A 9V bat-

tery must be installed in the CTG-1 to maintain clock time during a power outage. Either a standard or rechargeable

9V battery will maintain the clock time for over 8 hours.

Note: When using a rechargeable 9 volt battery, the battery charging jumper must be in the ON position (see diagram

above). When using a non-rechargeable 9 volt battery, this shunt must be in the OFF position.

Clock and Event Time Setting Buttons: Press

the + or -/CANCEL buttons to increase or

decrease time. The -/CANCEL switch is also

used to cancel an alert tone/buzzer sound event

when reviewing programming.

Alert Tones Programming Buttons: After set-

ting an event time, press SINGLE, DOUBLE or

TRIPLE to program 1, 2 or 3 alert tones/buzzer

sounds for that event time.

Secondary Button Functions While in the SET

DAY Mode: The SINGLE button is used to select

between day (1-7) or on/off. The DOUBLE but-

ton is used as a one time setup to program

today’s day of the week.

VIKING

MODEL CTG-1

CLOCK CONTROLLED

TONE GENERATOR

9V BATTERY

BACKUP

12345678910

ALERT TONE

VOLUME

LOCK

SET TIME

SET DAY

SET EVENTS

REVIEW/CANCEL

12:00

-/CANCEL + MODE

SINGLE DOUBLE TRIPLE

ALERT TONES

TIME

10 - Common

9 - Emergency Siren (Yelp): Continuous while

shorted to pin 10 (common).

8 - Evacuation Sound (Temporal Slow Whoop):

Continuous while shorted to pin 10 (common).

7 - Doorbell Chime Sound (Ding Dong): Repeated

continuously while shorted to pin 10 (common).

6 - Alert Tone/Buzzer*: Short to pin 10 (common) for

buzzer sound, leave open for tones.

5 - Normally Open Relay Contact

4 - Common Relay Connection

3 - Normally Closed Relay Contact

1 & 2 - 600 Ohm Audio Out Pair: Line level output,

connect to input of paging amplifier.

Battery Charge

Jumper

OFF

3 Normally Open

1 Common

2 Normally Closed

Secondary

Relay Contacts

Internal Battery Charge Jumper:

Factory set default is OFF. Note: For re-

chargeable batteries, move the Battery

Charge shunt to the ON position.

Internal Secondary Relay Contacts:

These activate in conjunction with pins 3, 4

and 5. You may solder to these PCB pads if

a second set of relay contacts are required.

Mode Button: Press to place the

CTG-1 in the Lock, Set Time, Set Day,

Set Events or Review/Cancel modes.

9V Battery Backup Connection: A standard

alkaline or rechargeable (NiCad/NiMh) 9V bat-

tery must be installed here to maintain the clock

time during power outages.

CTG-1 Output Volume Control: Turn clockwise

to increase volume of alert tones/buzzer sounds,

emergency and door bell (chime) sounds (see

diagram below).

VIKING

MODEL CTG-1

CLOCK CONTROLLED

TONE GENERATOR

9V BATTERY

BACKUP

12345678910

ALERT TONE

VOLUME

LOCK

SET TIME

SET DAY

SET EVENTS

REVIEW/CANCEL

12:00

-/CANCEL + MODE

SINGLE DOUBLE TRIPLE

ALERT TONES

TIME

Paging port

output of

PABX/KSU

PA-2A Paging/Loud Ringing

Amplifier System

Input of

Paging Amp

-or-

Volume

Control

Common

Siren

Evacuation Signal

Doorbell

Alert Tone/Buzzer Sound Select

(open = tones, closed = buzzer sounds)

Dry Contact Closures from Alarm

Equipment, Doorbell Switch, Etc.

Battery

PAGING - LOUD RINGING

AMPLIFIER SYSTEM

VIKING

ELECTRONICS

HUDSON, WI 54016

VIKING

MODEL PA-2A

POWER 13.8

V AC

12345678 910

NIGHT TRANSFER

SWITCH INP

PAG

ING

HORN

600 OHM

AUDIO OUT

PUT

TRUNK / PAGING

POR

DRY CONTACT

CLOSURE IN

PUT

RINGING

VOLUME

MAX

MIN

1 - 3 4 - 6

RINGING LINES

1 2 3 4

TALK BATTERY

ALERT TONE

WARBLE / CHIME

PAGING

VOLUME

MAX

MIN

POWER

JP1

Display: Shows

clock, event time

and mode set-

tings.

* Note: When the alarm buzzer is selected (pin 6 shorted to pin 10),

a double or triple programmed event will be sounded twice, approxi-

mately three seconds apart.

1 2 3 4

Commenti su questo manuale

Nessun commento

Viking CTG-2 Specifiche Pagina 2

Commenti su questo manuale

Prodotti e manuali riguardandi Orologi a muro Viking CTG-2